$70.75 Buy It Now or Best Offer
free,30-Day Returns
Seller Store
() %,
Location: Ontario, California, United States
Ships to: US,
Item: 264496398640
eBay 1.Fit For Acura Integra GS 1.8L 1997-2001 Acura Integra GS-R 1.8L 1994-2001 Acura Integra LS 1.8L 1994-2001 Acura Integra RS 1.8L 1994-1998 Acura Integra Special 1.8L 1995-1996 Acura Integra Type 1.8L 1997-2001 Honda Civic CX 1.5L 1992-1995 Honda Civic DX 1.5L 1992-1995 Honda Civic EX 1.6L 1992-1995 Honda Civic LX 1.5L 1992-1995 Honda Civic Si 1.6L 1992-1995 Honda Civic VX 1.5L 1992-1995 Honda Civic del Sol S 1.5L 1993-1995 Honda Civic del Sol S 1.6L 1996-1997 Honda Civic del Sol Si 1.6L 1993-1997 Honda Civic del Sol VTEC 1.6L 1994-1997 2.Package Includes: 1x Part# Front Left Upper Control Arm and Ball Joint Assembly – k90449 For 1994-00 2001 Acura Integra Suspension 10 Upper Control Arms Tie Rod Sway Bar 1.Fit For Acura Integra GS 1.8L 1997-2001 Acura Integra GS-R 1.8L 1994-2001 Acura Integra LS 1.8L 1994-2001 Acura Integra RS 1.8L 1994-1998 Acura Integra Special 1.8L 1995-1996 Acura Integra Type 1.8L 1997-2001 Honda Civic CX 1.5L 1992-1995 Honda Civic DX 1.5L 1992-1995 Honda Civic EX 1.6L 1992-1995 Honda Civic LX 1.5L 1992-1995 Honda Civic Si 1.6L 1992-1995 Honda Civic VX 1.5L 1992-1995 Honda Civic del Sol S 1.5L 1993-1995 Honda Civic del Sol S 1.6L 1996-1997 Honda Civic del Sol Si 1.6L 1993-1997 Honda Civic del Sol VTEC 1.6L 1994-1997 2.Package Includes: 1x Part# Front Left Upper Control Arm and Ball Joint Assembly – k90449 1x Part# Front Right Upper Control Arm and Ball Joint Assembly – K90448 2x Part# Front Lower Ball Joints – K9802 2x Part# Front Inner Tie Rods – EV299 1x Part# Front Left Outer Tie Rod – ES3332R 1x Part# Front Right Outer Tie Rod – ES3331R 2x Part# Front Sway Bar Links – K90123 Notes (1).Please check the fitment chart above before payment making sure all the suspension parts listed on this page are compatible with your automobile. (2).Please refer to Moog official website before narrowing down your search so as to avoid unnecessary item not as described return requests. (3).Please contact our customer services for targeted discount after all the items are received if you have reached any targeted discount thresholds, the terms of which is at the bottom of this page. If you are interested with any other suspension parts, please click and save our store. Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension. Picture(A) The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty. Picture(B) 1.Raise the vehicle and remove the front wheels. 2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes. Picture(C) 3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts. Picture(D) 4.Loosen and remove the fixing nut of the ball joint on the steering knuckle. Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket. Picture(E) 5.Remove the bad or worn ball joint from the control arm. 6.Loosen the compression ball joint on the steering knuckle using a suitable special tool. Picture(F) 7.Clean the cone connection. Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface. Picture(G) 8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts. 9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. 10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary. 11.Finally, carry out a test drive. Sway Bar Stabilizer Link Replacement Guideline: While driving, the following signs may indicate a faulty sway bar stabilizer link: (1).Rattling and thumping noises on rough roads. (2).Imprecise vehicle handling. (3).Stronger inclination of the vehicle during cornering. If the sway bar stabilizer link is found to be defective, it should be replaced as described below. Picture(A) 1.Raise vehicle and remove front wheels. Tip:Always check both stabilizer links and replace them in pairs if necessary. 2.Spray fastening nuts of the stabilizer link with rust remover and let act for a few minutes. Picture(B) 3.Loosen the lower fastening nut of the stabilizer link at the stabilizer and remove. Tip:If the ball stud also starts to turn, hold it with a suitable tool. 4.Press stabilizer link out of torsion bar. Picture(C) 5.Loosen the upper fastening nut of the stabilizer link at the suspension strut and remove it. Tip:If the ball stud also starts to turn, hold it with a suitable tool. Picture(D) 6.Press stabilizer link at suspension strut out of bracket. Picture(E) 7.Insert new stabilizer link at suspension strut. Picture(F) 8.Tighten stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(G) 9.Insert new stabilizer link at stabilizer. 10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(H) 11.Remount the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension. 12.Conclude with a test drive. Tie-Rod End Replacement Guideline: If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely. This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod. Picture(A) Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance. 1.Lift the vehicle and dismount the front axle wheels. 2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes. Picture(B) 3.Dismount the front underride guard. Picture(C) 4.Loosen the fastening nut from the tie rod and remove it completely. 5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator. Picture(D) 6.Remove the clamp of the bellow on the steering gear. 7.Push the bellow towards the tie rod end. Picture(E) 8.Unscrew the inner tie rod from the rack. 9.Clean the sealing face of the bellow at the steering gear. Picture(F) 10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle. Note:Always use new self-locking nuts and bolts for a reliable repair. 11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer. Picture(G) 12.Mount the bellow and close the clamps with the appropriate special tool. Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance. Picture(H) 13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer. Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure. Tip:Secure the ball stud against twisting with a suitable tool. Picture(I) 14.Mount the front underride guard. 15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer. 16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications. 17.Perform a test drive. Note:When performing the test drive, pay special attention to the handling while cornering and listen for possible noise emission. Frequently Asked Questions (1).Do I need to replace the control arm if the bushings are worn? Because the weight of the car is transferred through the control arm two rubber bushings are fitted at the pivot point and bolted to the frame. Road conditions and driving habits can contribute to the wear of these bushings which will become worn and fall apart. These bushing can be inspected by raising the car up and looking for an irregular configuration of the rubber center of the bushing. Many control arms have the ball joint manufactured into the arm which will be replaced along with the control arm itself. When one control arm is worn it is highly advised to replace the opposing arm. (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel. Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control. If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious. Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car. (3).What happens if I don’t replace ball joints? If you don’t want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new. (4).Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new one after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card. (5).Why should I get my tie rods inspected on a regular basis? If you don’t get your tie rods inspected on a regular basis, there are some warning signs to watch (and listen) for. If your vehicle pulls to one side while driving, or when braking, it’s possible that bad tie rods may be the culprit. Your vehicle’s tires will also show uneven wear on the inside and outside edge of the tire when there’s a tire rod issue. However, one of the most noticeable signs of tie rods going bad will be a knocking sound coming from the front end of the vehicle when you turn into a parking space, or some other low speed, tight turning situation. (6).Vibrations One of the first symptoms that your tie rods are damaged or breaking is that the steering wheel will vibrate slightly. This is especially prevalent when you are speeding up or turning. This happens because the steering wheel is losing its control over the tires, causing the steering wheel to shimmy as you drive. (7).Shaking As the tie rods become further damaged, you will start to notice that the car itself will start to shake. This happens because the tires may start to wobble without you having full control over them. Although you should take your car into a mechanic at the first sign of tie rod problems, if you experience your car shaking you could be at risk for serious tie rod damage-which can cause accidents. Take your car into a mechanic if you experience this tie rod symptom. (8).Wandering If your tie rods continue to go unchecked or unfixed, the rods can completely break. This can cause you to lose all control of your car, possibly resulting in an accident. When this occurs, the car will may “wander” as you drive. At this point, the steering wheel will have no control over the tires and the tires will start moving independently, causing the car to drift while you are driving. If this happens while you are on a freeway or busy road, you and others could be at serious risk of an accident. If you experience wandering, stop your car, call a tow truck and take your car to the nearest mechanic. (9).What are the symptoms of a bad sway bar? Some of the common symptoms of a bad sway bar bushing or sway bar links going bad are: clunking noise, rattling noise, knocking uneven noise road, lack of stability when driving and noise going over speed bumps. poor handling during turns. (10).What happens when a sway bar breaks? Because a sway bar helps the car’s suspension to put more pressure on loaded springs, a broken sway bar means that the car’s suspension will not be able to handle corners as well or as quickly. While it is possible to drive with a broken sway bar, as a precaution do not take corners with excessive speeds. Item Specifics Placement on Vehicle : Front Type : Control Arm & Ball Joint Assembly Universal Fitment : No Control Arm Construction : Forged Custom Bundle : Yes Interchange Part Number : K90448, K90449, K9802, K90123, EV299, ES3331R, ES3332R Bundle Description : Control Arm,Ball Joint,Stabilizer Bar Link,Tie Rod End OE/OEM Part Number : Suspension Control Arms and Ball Joints Assembly,Tie Rod Ends Superseded Part Number : Front Driver and Passenger Side Replacement Manufacturer Warranty : 10 Year Brand : topcn-autoparts UPC : Does Not Apply Manufacturer Part Number : TA80984701P Adjustable : Yes Greasable or Sealed : Greasable Kit Included : 10 Pieces Surface Finish : Premium Quality Cross Part Number : 51450SR3023, 51460SR3023, 51220SO4003, 51220SR0A01, 51220SR3003 Cross Reference Part Number : 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 Partlink Number : 53540S04013, 53540SO3003, 53540SO3013, 53540SR0A01, 53540SR3003 Fitment : For Acura Integra Honda Civic Honda Civic del Sol Suspension Grade : Standard Suspension Grade : Standard Features : Greasable Finish : Coated Cotter Pin Hole : Yes Material : Alloy Steel Mounting Style : Bolt-On Discount Targeted Discounts Terms (1).Targeted Discount Terms only apply to auto parts purchased from Topcn-autoparts, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).If you have reached any targeted discount threshold(s), please contact our customer services after you received all your items. (3).Targeted Discount will be refunded from buyer’s payment, which means Topcn-autoparts won’t provide any extra targeted discounts if full refund is issued. Targeted Shipping Discount (4).Since our warehouse is located in Los Angeles, California, therefore you are qualified for extra 2% targeted shipping discount off the item sales if shipping address of your order is in California(CA), Washington(WA), Oregon(OR), Nevada(NV). If you have reached this targeted shipping discount threshold, please contact our customer services after you received all your items. Note: Item sales means your payment for the product(s) only, excluding shipping and handling charges, US internet sales taxes. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Topcn-autoparts has the final power of interpretation of all the above Targeted Discount Terms and Procedures. Shipping WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm. (1).Warehouse is located in Los Angeles, California, where local pickup transaction is temporarily not available. (2).Shipping services only cover 48 states and Washington DC in US Continental, while most of the time Alaska, Hawaii, Puerto Rico, American Samoa, U.S. Virgin Islands, Northern Marianas, Guam are not deliverable. (3).USPS PO Box, APO Army Post Office, FPO Fleet Post Office addresses are not available. (4).Global Shipping Program is temporarily not available due to the reason for package dimensions. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Your auto parts sometimes might be shipped with two or more separated packages due to weight limitation, please keep patient with no Item Not Received claim or Return request filed until by all of your items are received. (7).Seller is required to purchase signature confirmation to be protected if a buyer reports an item not received or opens a payment dispute if the order has a total cost (including shipping costs and any taxes) of $750 or more. Warranty Items valued over $15 on eBay that include a warranty or service contract must contain additional details in seller’s listing description. 10 Year Warranty Terms and Procedures (1).The warranty terms only apply to the auto parts purchased from Topcn-autoparts, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).Topcn-autoparts carries no warranty responsibilities for any auto parts removing fees, installation fees, consulting fees, labor costs, towing charges, rental car reimbursements. (3).The stated 10 year warranty is limited to only one brand new replacement for each part purchased during 10 year warranty time period. (4).Topcn-autoparts promises free replacement due to quality defects or item not as described issues within 90 calendar days from the date when buyers receive their items in the situation when buyers are willing to provide convictive proofs or professional diagnose report if required, otherwise Topcn-autoparts has the right to refuse any replacement requests. (5).Topcn-autoparts promises free replacement due to quality defects or item not as described issues after 90 calendar days from the date when buyers receive their items in the situation when buyers promise to prepay 15% of the original item sales price as postage for replacement, otherwise Topcn-autoparts has the right to refuse any replacement requests. (6).Topcn-autoparts carries no warranty responsibilities for any replacement due to car accidents, drag racing, unprofessional replacement, road hazard, disassembly. (7).Anyone who attempts to execute 10 year warranty procedures must be the original purchaser of the item(s), otherwise 10 year warranty terms void immediately. (8).Anyone who attempts to execute 10 year warranty procedures must provide screenshot of his or her original eBay order details if required, including buyer user name, shipping address, item title, item id, final sales price. (9).Topcn-autoparts has the final power of interpretation of the above 10 Year Warranty Terms and Procedures. Return (1).Most of items support 60 Days Money Back Guarantee. (2).Refunds will be credited within 2 or 3 business days after returned item(s) is received. Best Sales Upstream & Downstream Oxygen O2 02 Sensor For 2001-2005 Honda Civic 1.7L D17A7 USD 26.85 2x Front Hood Gas Lift Supports Struts Shocks Springs For Dodge Ram 02-10 4364 USD 16.81 2 X Front/Rear Wheel Hub Bearing For Buick LaCrosse Century Chevy Impala Venture USD 63.53 Pair Front Wheel Bearings For Chevrolet Impala Buick Pontiac Grand Prix Montana USD 62.35 2x Front Hood Lift Supports Shocks Struts For Dodge Ram 1500 2500 3500 4500 5500 USD 13.49 Newly Listed Power Heated Memory RH Side Mirror For 2000-2006 BMW X5 Series E53 51168408810 USD 167.49 Set of 2 For 2004-08 Pontiac Grand Prix Side View Black Mirrors Power Heated USD 72.99 Clear LH Power Manual Telescoping Black Mirror For 03-14 Ford Econoline USD 44.99 4X Brake Metallic Pads Rear For 88 89 90 91 92 93 94 95 96 Chevrolet Corvette USD 36.80 Motorcycle Side Rearview Mirrors Aluminum 7/8″ Handle Bar End 3″ Round Aluminum USD 18.38 Terms & Contact Shipping Policy Payment Policy Return Policy FAQ About Us For 1994-00 2001 Acura Integra Suspension 10 Upper Control Arms Tie Rod Sway Bar 1.Fit For Acura Integra GS 1.8L 1997-2001 Acura Integra GS-R 1.8L 1994-2001 Acura Integra LS 1.8L 1994-2001 Acura Integra RS 1.8L 1994-1998 Acura Integra Special 1.8L 1995-1996 Acura Integra Type 1.8L 1997-2001 Honda Civic CX 1.5L 1992-1995 Honda Civic DX 1.5L 1992-1995 Honda Civic EX 1.6L 1992-1995 Honda Civic LX 1.5L 1992-1995 Honda Civic Si 1.6L 1992-1995 Honda Civic VX 1.5L 1992-1995 Honda Civic del Sol S 1.5L 1993-1995 Honda Civic del Sol S 1.6L 1996-1997 Honda Civic del Sol Si 1.6L 1993-1997 Honda Civic del Sol VTEC 1.6L 1994-1997 2.Package Includes: 1x Part# Front Left Upper Control Arm and Ball Joint Assembly – k90449 1x Part# Front Right Upper Control Arm and Ball Joint Assembly – K90448 2x Part# Front Lower Ball Joints – K9802 2x Part# Front Inner Tie Rods – EV299 1x Part# Front Left Outer Tie Rod – ES3332R 1x Part# Front Right Outer Tie Rod – ES3331R 2x Part# Front Sway Bar Links – K90123 Notes (1).Please check the fitment chart above before payment making sure all the suspension parts listed on this page are compatible with your automobile. (2).Please refer to Moog official website before narrowing down your search so as to avoid unnecessary item not as described return requests. (3).Please contact our customer services for targeted discount after all the items are received if you have reached any targeted discount thresholds, the terms of which is at the bottom of this page. If you are interested with any other suspension parts, please click and save our store. Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension. Picture(A) The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty. Picture(B) 1.Raise the vehicle and remove the front wheels. 2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes. Picture(C) 3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts. Picture(D) 4.Loosen and remove the fixing nut of the ball joint on the steering knuckle. Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket. Picture(E) 5.Remove the bad or worn ball joint from the control arm. 6.Loosen the compression ball joint on the steering knuckle using a suitable special tool. Picture(F) 7.Clean the cone connection. Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface. Picture(G) 8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts. 9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. 10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary. 11.Finally, carry out a test drive. Sway Bar Stabilizer Link Replacement Guideline: While driving, the following signs may indicate a faulty sway bar stabilizer link: (1).Rattling and thumping noises on rough roads. (2).Imprecise vehicle handling. (3).Stronger inclination of the vehicle during cornering. If the sway bar stabilizer link is found to be defective, it should be replaced as described below. Picture(A) 1.Raise vehicle and remove front wheels. Tip:Always check both stabilizer links and replace them in pairs if necessary. 2.Spray fastening nuts of the stabilizer link with rust remover and let act for a few minutes. Picture(B) 3.Loosen the lower fastening nut of the stabilizer link at the stabilizer and remove. Tip:If the ball stud also starts to turn, hold it with a suitable tool. 4.Press stabilizer link out of torsion bar. Picture(C) 5.Loosen the upper fastening nut of the stabilizer link at the suspension strut and remove it. Tip:If the ball stud also starts to turn, hold it with a suitable tool. Picture(D) 6.Press stabilizer link at suspension strut out of bracket. Picture(E) 7.Insert new stabilizer link at suspension strut. Picture(F) 8.Tighten stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(G) 9.Insert new stabilizer link at stabilizer. 10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(H) 11.Remount the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension. 12.Conclude with a test drive. Tie-Rod End Replacement Guideline: If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely. This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod. Picture(A) Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance. 1.Lift the vehicle and dismount the front axle wheels. 2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes. Picture(B) 3.Dismount the front underride guard. Picture(C) 4.Loosen the fastening nut from the tie rod and remove it completely. 5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator. Picture(D) 6.Remove the clamp of the bellow on the steering gear. 7.Push the bellow towards the tie rod end. Picture(E) 8.Unscrew the inner tie rod from the rack. 9.Clean the sealing face of the bellow at the steering gear. Picture(F) 10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle. Note:Always use new self-locking nuts and bolts for a reliable repair. 11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer. Picture(G) 12.Mount the bellow and close the clamps with the appropriate special tool. Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance. Picture(H) 13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer. Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure. Tip:Secure the ball stud against twisting with a suitable tool. Picture(I) 14.Mount the front underride guard. 15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer. 16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications. 17.Perform a test drive. Note:When performing the test drive, pay special attention to the handling while cornering and listen for possible noise emission. Frequently Asked Questions (1).Do I need to replace the control arm if the bushings are worn? Because the weight of the car is transferred through the control arm two rubber bushings are fitted at the pivot point and bolted to the frame. Road conditions and driving habits can contribute to the wear of these bushings which will become worn and fall apart. These bushing can be inspected by raising the car up and looking for an irregular configuration of the rubber center of the bushing. Many control arms have the ball joint manufactured into the arm which will be replaced along with the control arm itself. When one control arm is worn it is highly advised to replace the opposing arm. (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel. Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control. If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious. Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car. (3).What happens if I don’t replace ball joints? If you don’t want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new. (4).Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new one after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card. (5).Why should I get my tie rods inspected on a regular basis? If you don’t get your tie rods inspected on a regular basis, there are some warning signs to watch (and listen) for. If your vehicle pulls to one side while driving, or when braking, it’s possible that bad tie rods may be the culprit. Your vehicle’s tires will also show uneven wear on the inside and outside edge of the tire when there’s a tire rod issue. However, one of the most noticeable signs of tie rods going bad will be a knocking sound coming from the front end of the vehicle when you turn into a parking space, or some other low speed, tight turning situation. (6).Vibrations One of the first symptoms that your tie rods are damaged or breaking is that the steering wheel will vibrate slightly. This is especially prevalent when you are speeding up or turning. This happens because the steering wheel is losing its control over the tires, causing the steering wheel to shimmy as you drive. (7).Shaking As the tie rods become further damaged, you will start to notice that the car itself will start to shake. This happens because the tires may start to wobble without you having full control over them. Although you should take your car into a mechanic at the first sign of tie rod problems, if you experience your car shaking you could be at risk for serious tie rod damage-which can cause accidents. Take your car into a mechanic if you experience this tie rod symptom. (8).Wandering If your tie rods continue to go unchecked or unfixed, the rods can completely break. This can cause you to lose all control of your car, possibly resulting in an accident. When this occurs, the car will may “wander” as you drive. At this point, the steering wheel will have no control over the tires and the tires will start moving independently, causing the car to drift while you are driving. If this happens while you are on a freeway or busy road, you and others could be at serious risk of an accident. If you experience wandering, stop your car, call a tow truck and take your car to the nearest mechanic. (9).What are the symptoms of a bad sway bar? Some of the common symptoms of a bad sway bar bushing or sway bar links going bad are: clunking noise, rattling noise, knocking uneven noise road, lack of stability when driving and noise going over speed bumps. poor handling during turns. (10).What happens when a sway bar breaks? Because a sway bar helps the car’s suspension to put more pressure on loaded springs, a broken sway bar means that the car’s suspension will not be able to handle corners as well or as quickly. While it is possible to drive with a broken sway bar, as a precaution do not take corners with excessive speeds. Item Specifics Placement on Vehicle : Front Type : Control Arm & Ball Joint Assembly Universal Fitment : No Control Arm Construction : Forged Custom Bundle : Yes Interchange Part Number : K90448, K90449, K9802, K90123, EV299, ES3331R, ES3332R Bundle Description : Control Arm,Ball Joint,Stabilizer Bar Link,Tie Rod End OE/OEM Part Number : Suspension Control Arms and Ball Joints Assembly,Tie Rod Ends Superseded Part Number : Front Driver and Passenger Side Replacement Manufacturer Warranty : 10 Year Brand : topcn-autoparts UPC : Does Not Apply Manufacturer Part Number : TA80984701P Adjustable : Yes Greasable or Sealed : Greasable Kit Included : 10 Pieces Surface Finish : Premium Quality Cross Part Number : 51450SR3023, 51460SR3023, 51220SO4003, 51220SR0A01, 51220SR3003 Cross Reference Part Number : 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 Partlink Number : 53540S04013, 53540SO3003, 53540SO3013, 53540SR0A01, 53540SR3003 Fitment : For Acura Integra Honda Civic Honda Civic del Sol Suspension Grade : Standard Suspension Grade : Standard Features : Greasable Finish : Coated Cotter Pin Hole : Yes Material : Alloy Steel Mounting Style : Bolt-On DiscountShippingWarrantyReturnFeedback Targeted Discounts Terms (1).Targeted Discount Terms only apply to auto parts purchased from Topcn-autoparts, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).If you have reached any targeted discount threshold(s), please contact our customer services after you received all your items. (3).Targeted Discount will be refunded from buyer’s payment, which means Topcn-autoparts won’t provide any extra targeted discounts if full refund is issued. Targeted Shipping Discount (4).Since our warehouse is located in Los Angeles, California, therefore you are qualified for extra 2% targeted shipping discount off the item sales if shipping address of your order is in California(CA), Washington(WA), Oregon(OR), Nevada(NV). If you have reached this targeted shipping discount threshold, please contact our customer services after you received all your items. Note: Item sales means your payment for the product(s) only, excluding shipping and handling charges, US internet sales taxes. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Topcn-autoparts has the final power of interpretation of all the above Targeted Discount Terms and Procedures. WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm. (1).Warehouse is located in Los Angeles, California, where local pickup transaction is temporarily not available. (2).Shipping services only cover 48 states and Washington DC in US Continental, while most of the time Alaska, Hawaii, Puerto Rico, American Samoa, U.S. Virgin Islands, Northern Marianas, Guam are not deliverable. (3).USPS PO Box, APO Army Post Office, FPO Fleet Post Office addresses are not available. (4).Global Shipping Program is temporarily not available due to the reason for package dimensions. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Your auto parts sometimes might be shipped with two or more separated packages due to weight limitation, please keep patient with no Item Not Received claim or Return request filed until by all of your items are received. (7).Seller is required to purchase signature confirmation to be protected if a buyer reports an item not received or opens a payment dispute if the order has a total cost (including shipping costs and any taxes) of $750 or more. Items valued over $15 on eBay that include a warranty or service contract must contain additional details in seller’s listing description. 10 Year Warranty Terms and Procedures (1).The warranty terms only apply to the auto parts purchased from Topcn-autoparts, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).Topcn-autoparts carries no warranty responsibilities for any auto parts removing fees, installation fees, consulting fees, labor costs, towing charges, rental car reimbursements. (3).The stated 10 year warranty is limited to only one brand new replacement for each part purchased during 10 year warranty time period. (4).Topcn-autoparts promises free replacement due to quality defects or item not as described issues within 90 calendar days from the date when buyers receive their items in the situation when buyers are willing to provide convictive proofs or professional diagnose report if required, otherwise Topcn-autoparts has the right to refuse any replacement requests. (5).Topcn-autoparts promises free replacement due to quality defects or item not as described issues after 90 calendar days from the date when buyers receive their items in the situation when buyers promise to prepay 15% of the original item sales price as postage for replacement, otherwise Topcn-autoparts has the right to refuse any replacement requests. (6).Topcn-autoparts carries no warranty responsibilities for any replacement due to car accidents, drag racing, unprofessional replacement, road hazard, disassembly. (7).Anyone who attempts to execute 10 year warranty procedures must be the original purchaser of the item(s), otherwise 10 year warranty terms void immediately. (8).Anyone who attempts to execute 10 year warranty procedures must provide screenshot of his or her original eBay order details if required, including buyer user name, shipping address, item title, item id, final sales price. (9).Topcn-autoparts has the final power of interpretation of the above 10 Year Warranty Terms and Procedures. (1).Most of items support 60 Days Money Back Guarantee. (2).Refunds will be credited within 2 or 3 business days after returned item(s) is received. Copyright of Topcn-autoparts. All rights reserved.
Frequently Asked Questions About For 1994-00 2001 Acura Integra Suspension 10 Upper Control Arms Tie Rod Sway Bar in My Website
enigmafiber.com is the best online shopping platform where you can buy For 1994-00 2001 Acura Integra Suspension 10 Upper Control Arms Tie Rod Sway Bar from renowned brand(s). enigmafiber.com delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.
What are the best-selling For 1994-00 2001 Acura Integra Suspension 10 Upper Control Arms Tie Rod Sway Bar on enigmafiber.com?
enigmafiber.com helps you to shop online and delivers Belstaff to your doorstep. The best-selling Belstaff on enigmafiber.com are: Belstaff Jacket Cream Canvas Biker Women’s size S Vintage Belstaff England Mens Sz L Black Winter Jacket Coat Liner Motorcycle EUC BELSTAFF Size 34 Green Cotton Blend Skinny 5 Pocket Jeans Mens BELSTAFF Black/Gray/Red Biker Motorcycle Leather Suit Size 44 $525 Belstaff Ivory Fisherman Sweater NWOT Large GORGEOUS Belstaff Mclaren nylon black jacket size Xl Belstaff 4 Pocket Padded Jacket Black 58283007 Used 2c993aa63ca4b80eb7016a9f912b BELSTAFF TRIALMASTER GREEN WAXED COTTON JACKET SIZE 38/40 M/L TRUE VINTAGE RARE Belstaff BV19 col.314 Eyeglasses Frames Ivory Silver Rectangular Size 55-15-130 BELSTAFF Womens Utility Jacket IT 42 Medium Black Cotton HZ03 Belstaff Women’s Black Langtry Velvet Asymmetrical Moto Jacket Coat Size M (38) BELSTAFF Trial Master Oiled Blouson Jacket Coat men USA 40 Vintage from JP Belstaff Vest Navy Blue Quilted Lightweight Women’s size 42 Belstaff Trialmaster inner down included Belstaff Temple Technical Nylon Motorcycle Jacket – Black BELSTAFF jacket beige MT00692 Belstaff Anderson Leather Motorcycle Lightweight Riding Boots Belstaff Men’s Brown Multipocket Waxed Racing Jacket Size 2XL BELSTAFF WOMENS ITALY SIDNEY TAN LEATHER SHORT MOTO JACKET IT 38 US S Belstaff Mens Puffer Jacket Padded Black Down Filled size 50 / M BELSTAFF Men’s Pathfield Navy Blue Diamond Quilted Jacket – Size 50 (L) Belstaff Shiny Women’s Quilted Jacket | Vintage High End Luxury Designer Black BELSTAFF Mens Steel Green Varial Quilted Jacket SIZE UK38 IT48 MEDIUM BNWT BELSTAFF size IT 40 – S – M Black VALTHERM Waistcoat Gilet Vest Logo BELSTAFF Walton Stud-Embellished Silk Blouse, 36 $795 BELSTAFF Men’s Faded Black Wash Stitched Detail Waxed Denim Slim Moto Jeans BELSTAFF ELLERSLY Nylon Parka Hooded JACKET Black Oversized IT48 UK16 RRP £530 Belstaff Men’s The Tide Quarter Zip Knitwear Pullover Sweater Navy XXL Slim Belstaff Men’s Beige Silk Multipocket Motorcycle Jacket Size 46 VINTAGE 70s BELSTAFF TRIALMASTER WAX COTTON MOTORCYCLE JACKET SIZE M SHABBY CHIC BELSTAFF GOLD LABEL WAXED JACKET Medium Hooded Rabbit Lapin Fur Trim Quilted Knit Cotton Belstaff Professional Motorcycle Biker Light Jacket Coat Size M BELSTAFF TUNSTALL COATED DENIM BIKER JACKET BLACK UK38 MEDIUM RRP £375 SUPERB Belstaff Virgin Wool & Cashmere Knit Jumper Grey – Size XS womens belstaff antrim jacket (motorcycle jacket) Black IT 48 US 12 Belstaff Waxed Motorcycle Denim Jeans Black Slim Fit Biker Moto Mens Size 29×33 NWT $380 Belstaff Burgundy Hybrid Soft Shell Shift Jacket Men’s 52 L AUTHENTIC Belstaff blue navy Quilted Vest Men’s Size 54 “Large” BELSTAFF Mens Elbow Patches Red Distressed Waxed Cotton Kelland Jacket SIZE 44 Bellstaff Quilted Gilet Mens Size 48 UK M Black VINTAGE 80’S BELSTAFF TRIALMASTER PRO WAXED COTTON MOTORCYCLE JACKET SIZE S BELSTAFF Limited Brown Leather Moto Biker Racer Jacket Coat – EU 46 / US 36 / S Belstaff Hitchin Extra Trim Fit Piqué Polo Mens size L Gray Logo Arm Quilted Vintge Belstaff Leather Motorcycle Jacket Size UK 12 In Black Women’s Twin Track BELSTAFF TRIALMASTER XL500 ENGLAND Motorcycle Jacket Vinta 1970s 80s Black Small Belstaff Men’s Silver Label Full Zip Nylon Jacket Gray Size Large BELSTAFF Men’s Wave Dye Phoenix Patch Sweatshirt – XL – Excellent Condition BELSTAFF Womens Snakeskin Black Leather Jacket – Size 40 RRP £799 Belstaff Men’s Wayfare Overshirt Memory Shell Jacket Black Size Small Belstaff Hampstead Leather Motorcycle Gloves – Forest Green Belstaff Parka Coat Size UK 10 IT 40 Waxed Camouflage Hooded *Wear* Belstaff women’s quilted Waistcoat Gilet Black English Jacket Pockets Size S Belstaff Black Prince 2000s Print Advertisement 2005 Leather Couple Kissing Belstaff Geoffston Down Fill Puffer Gilet Blue Size IT 46 UK Small Designer RARE Belstaff Soraya Asymmetrical Intarsia Sweater Made In Italy EUC Belstaff Marshall Leather Boots – Black – Size 10 – Premium Quality #319 Belstaff Fieldmaster Waxed Cotton Jacket Size 50-40 RETAIL $695 VINTAGE 80’S BELSTAFF TRIALMASTER PRO WAXED COTTON MOTORCYCLE JACKET SIZE S Mens Belstaff Tonal Streamline Down Jacket Sz UK46 IT56 Faded Teal BNWT RRP £350 Belstaff Sticker Motorsport Bike Scooter Lambretta Style Decal 150mm / 6″ Black Prince By Belstaff FREE TIBET Short Sleeve T Shirt EU Size 44 New Crewneck BELSTAFF Leather Jacket Mens UK38 EU48 Blue Trelow Biker Bomber Moto Celebrity Mens Vintage Genuine Belstaff Raincoat Jacket Field Hunting Outdoor Size L Belstaff Goodwood Mens Sweater, Sz XL, Stripe Block On Green, 100% Wool Italy VINTAGE 80’S BELSTAFF LEATHER MOTORCYCLE TROUSERS SIZE TO FIT WAIST 26″ Belstaff Gold Label Women’s Fur Jacket Vintage Belstaff Cotton Jersey T-Shirt Tile Green Belstaff Rallymaster nylon multopocket gold label jacket size M VINTAGE BRITTON BY BELSTAFF WAXED COTTON HUNTING JACKET SIZE L Genuine Belstaff Women Crocodile Embossed Red Leather Belt EU Size 75 Italy Men’s BELSTAFF GOLD LABEL Insulated Leather Trim Nylon Biker Jacket Black Size S Belstaff Mens Leather Jacket. 54:L. $5400 Vintage Belstaff Trialmaster Gray Motorcycle Nylon Jacket Belstaff Men’s or Women’s SUEDE LEATHER authentic Jacket MiLitary STYLE Men Belstaff Motorcycle Biker Jacket BLUE Nylon Padded Armoured Size MEDIUM BELSTAFF Bomber Jacket Men’s Navy Blue Size 44-46 Mens Belstaff Vent Goretex Infinium Jacket Size UK 48 IT 58 Black BNWT RRP £475 belstaff hoodie S Belstaff Waxed Parka – Womens EU size 42 (L) 2004 Belstaff 80th Anniversary Collection Jeans High Boots Vintage Print Ad Vintage Belstaff Quilted Jacket Bomber Coat Jacket Men’s Small S Black Zip Up Belstaff Gold Label Women’s Brown Hooded Fur Jacket Coat Size 46 Made in Italy Belstaff × Merrell 1TRL Ontario Speed Size 8 VINTAGE 40’S BELSTAFF SUPERSENIA TT STORMCOAT MOTORCYCLE JACKET SIZE L New Belstaff Woodbridge Black Leather Jacket Genuine Leather IT 54 US 44 Belstaff & Loro Piana Storm System Wool Heavy Jacket Coat Size XL Made In Italy 70s Belstaff Trialmaster Rare Wax Motorcycle Bike Jacket Xs S Pants 68 cm 26″ BELSTAFF Sz 44 = 12 /14 Midnight Blue Down Puffer RARE leather Belt Jacket Vintage Belstaff Trailmaster Patch Waxed Jacket Brown Mens Size M $1400 Authentic Belstaff Black Label White Nappa Leather Ratchel Skirt Size 44 Belstaff Silver Label Nylon Biker Jacket Size 2XL Womans Outdoors Reflective Zip BELSTAFF Women’s Nylon Full-Zip Black Motorcycle Biker Insulated Jacket 44 L-XL BELSTAFF Mens White Coteland T Shirt SIZE MEDIUM Authentic BNWT Phoenix Logo BELSTAFF Men’s Reeve Indigo Leather Jacket – Very Good Condition Authentic BELSTAFF trailmaster painted biker motorcycle leather jacket size 40 New Men’s Belstaff Track Logo-Perforated Leather Sneakers Shoes Off-White 7.5 Belstaff Bomber Jacket Boys 8 Tan Biker Waxed Cotton Patina Needs Dry Cleaning Belstaff Kutum Leather Jacket Mens Size L Men’s BELSTAFF TOWN MASTER Jumpsuit Size S Extremely rare 70s-80s Britton Belsaff oiled jacket Mens Pullover Fleece Hoodie